ROUTINE CLEANING
Before beginning any cleaning procedure, unplug the brewer to avoid the
accidental start of a brew cycle. Clean the pod holder, drip tray and drip tray
grate after each use, using a damp cloth and mild detergent and rinse. With the
pod holder and drip tray removed, use a damp cloth with mild detergent to wipe
the area below the pod holder and into the drip tray area. Occasionally, wipe
the outside of the brewer with a damp cloth. (The reservoir, slide lid, pod
holder, drip tray and drip tray grate are dishwasher safe.)
PERIODIC
CLEANING/DESCALING
(Recommended At Least Once a Month.)
Periodically, you should clean and descale the
brewer to clear any mineral deposits that may have accumulated due to impurities
in the water source. If these deposits are not removed, they can impair the
operation of the brewer and reduce the product life. There are several products
available specifically for descaling. We recommend using URNEX Activated
Descaler or JavaClean2 Cleaner and Descaler. (White vinegar can be used to
descale if a descaling product is not available.) Follow the directions as
printed on the manufacturers package.
|
1.
|
 |
Fill the
reservoir with descaling product as described by the manufactures directions, or 1 quart (32 oz.) of white vinegar. Do not add powder mix
directly to the reservoir. Descaling product must be mixed into a solution
before it is added to the reservoir). |
|
2.
|
|
Place an empty
pod holder into the brewer. Be sure the holder is locked into place, and
set the VOLUME CONTROL SLIDE LEVER to the maximum position. (12 oz.) |
|
3.
|
|
Place an empty
cup or bowl on the drip tray grate that will hold at least 14 oz. of
liquid, and press the COFFEE BREW BUTTON to start a brew cycle. |
|
4.
|
|
Once the brew
cycle has finished, empty the cup and set it back onto the drip tray
grate. Press the COFFEE BREW BUTTON again to start a second brew cycle. |
|
5.
|
|
Once the brew
cycle has finished, empty the cup and the remaining solution, or vinegar
from the reservoir. Remove the Pod Holder; clean the reservoir and pod
holder thoroughly using a mild detergent, then rinse. |
| |
|
NOTE: There is now descaling solution in the
internal tank. Follow the manufactures directions if the solution must
be left in the tank for any period of time. For vinegar, allow the
solution to sit for at least two, but no more that four hours. |
|
6. |
|
Fill the
reservoir to the maximum line with fresh clean cold water and place the
pod holder back into the brewer. |
|
7. |
|
Place the empty cup or bowl back onto the drip tray grate and press the
COFFEE BREW BUTTON to begin a brew cycle. |
|
8. |
|
When the cycle has finished, empty the cup. Repeat step 7 at least two
more times to remove the solution from the tank. |
|
9. |
|
Clean the pod
holder with a mild detergent and rinse thoroughly. |
|
10. |
|
Proceed to the
Cleaning The Sprayhead/Seal section. |
CLEANING THE
SPRAYHEAD / SEAL
|
1.
|
|
Press the Power
Switch into the off position. |
|
2.
|
|
Unplug the
brewer and allow it to cool down. (Minimum of 1 hour.) |
|
3.
|
|
After the unit
has been allowed to cool, remove the pod holder and set aside. |
|
4.
|
|
Using your
fingers, rotate the sprayhead/seal assembly clockwise until the sprayhead
and seal are removed. |
| |
|
NOTE: If the sprayhead and seal are separated, they must be
reassembled as they were when removed from the brewer.
NOTE: See Assembling Sprayhead/Seal and
Inspecting Sprayhead Seal located further down page
for more information. |
|
5.
|
|
Clean the
sprayhead and seal with a mild detergent and rinse thoroughly. |
|
6.
|
|
Using your
fingers, rotate the sprayhead/seal assembly counter-clockwise until it is
finger tight. |
|
7.
|
|
Replace the pod
holder. |
|
8.
|
|
Plug in the
brewer and press the POWER SWITCH to restore power to the brewer. |
|
10.
|
|
Place decanter
on base plate and plug in the brewer. Allow the water in the tank to reach
brewing temperature before using (approximately 15 minutes). |
ASSEMBLING THE
SPRAYHEAD / SEAL If the sprayhead and seal are
separated during removal or cleaning, they must be reassembled properly.
|
1.
|
|
Identify the top
of the seal. The top of the seal that seats against the roof of the
sprayhead ramp has a rough ridge that can be felt by running your fingers
across the surface of the seal. The bottom is smooth. |
|
2.
|
|
Identify the top
of the sprayhead. The top of the sprayhead has a star pattern and a threaded
hole where the sprayhead attaches to the brewer. |
|
3.
|
|
While carefully
stretching the seal, guide the sprayhead into the channel of the seal. Make
sure it is completely in the channel. |
When properly assembled, the sprayhead will
slide easily into the channel of the seal and will not cause any buckles in the
surface of the seal. If the sprayhead seems to be difficult to seat, and you
must stretch the seal more than a slight tug, the assembly is not together
correctly.
INSPECTING THE
SPRAYHEAD SEAL
When disassembling your brewer for cleaning,
inspect the sprayhead seal for cracks, tears and holes. Although the seal should
last for an extended period of time, damage can occur through handling.
Replace the seal if it becomes damaged.
CLEANING THE
POD HOLDER
To prevent residue build up, it is a good idea to
periodically disassemble the pod holder/screen assembly and clean it with a mild
detergent.
|
1.
|
|
Press and hold the POD RELEASE BUTTON while sliding the pod holder out. |
|
2.
|
|
Flip the POD HOLDER upside down and place the holder cavity over the palm of
your hand. |
|
3.
|
|
Using a small object, press the tab of the POD HOLDER INSERT through the
hole in the bottom of the pod holder to remove. |
|
4.
|
|
Clean the screen and holder using a mild detergent and rinse. (Dishwasher
Safe) |
|
5.
|
|
Press the insert back through the hole in the bottom of the POD HOLDER. |
CYCLING THE
BREWER
If the brewer has not been used for an extended period of time, it is a good
idea to cycle your brewer before brewing a cup of coffee or tea.
|
1.
|
|
Remove the reservoir and pod holder from the brewer, clean with a mild
detergent and rinse. |
|
2.
|
|
Refill the reservoir to the maximum line. |
|
3.
|
|
Insert an empty pod holder into the brewer. |
|
4.
|
|
Set
the volume control lever to the maximum setting. |
|
5.
|
|
Place a bowl or cup on the drip tray grate that will hold at least 14 oz. |
|
6. |
|
Press the coffee brew button. |
|
7. |
|
When the brew cycle has ended and water drip out has stopped, carefully
remove the pod holder and remove any excess water. |
You are now ready to brew.
STORING THE
BREWER
Unplug the brewer and wait for it to cool. If your Pod brewer has been used, it
must be stored above 32 F to
prevent damage to the internal water tank. Empty and dry the water reservoir
before storing. NOTE: Water will remain in the internal tank. If stored for an
extended period of time, refer to Cycling The Brewer section above before
using.
