 |
|
|
|
|
Problem |
|
Suggestions |
|
|
|
|
|
Nothing happens when the COFFEE BUTTON is pressed |
This is the first time
you have used your brewer. |
|
|
The Initial Brewer
Set-up procedure must be performed first.
Please download these
directions before
attempting to run a brew cycle. |
|
Your brewer is not
plugged in. |
|
|
Check to make sure the
brewer is plugged in and the POWER SWITCH has been turned on. (The
POD HOLDER RELEASE BUTTON - also known as the BUNN Indicator - will
be illuminating red, indicating power to the brewer.) |
|
The HEATING INDICATOR is
lit. |
| |
Wait until the indicator
goes off before pressing one of the brew buttons. The brewer will
not start a brew cycle until the water in the internal tank is
heated to the proper temperature. |
| |
The POD HOLDER INDICATOR
is lit. |
| |
Check to make sure the
POD HOLDER is inserted into the brewer. If the POD HOLDER is
inserted into the brewer, carefully remove and replace the POD
HOLDER to ensure the POD HOLDER is locked in place. Listen for a
clicking sound. The click indicates that the holder has locked into
place. |
| |
The REFILL WATER
INDICATOR is lit. |
| |
The reservoir has run
low on water and needs to be filled above the minimum mark indicated
on the side of the reservoir. |
|
|
|
|
|
The
REFILL WATER INDICATOR has come on |
The WATER RESERVOIR has
run low on water. |
|
|
Slide the lid open and
pour additional water into the reservoir, or remove the reservoir
and fill it at a sink, or other water source. |
| |
|
|
|
|
|
The
POD HOLDER INDICATOR has come on |
The POD HOLDER is
missing. |
|
|
Place the pod holder
into the machine and press it firmly into place. |
|
The POD HOLDER is not
locked in place. |
|
Carefully remove and
re-insert the pod holder into the machine while listening for a
clicking sound. The POD HOLDER INDICATOR on the control panel should
go out. |
|
|
|
|
|
The
water shuts off and comes back on again when brewing |
The TEA BREW BUTTON has
been pressed to start the brew cycle. |
|
|
DO NOT press the
TEA BREW or COFFEE BREW button during the brew cycle. This will stop
the brew cycle. The
brewer is using a Pulse Brew technology to steep tea properly. The
water will shut off and turn on again. This is normal and will take
about 45 seconds to complete. Wait for the blue lights to go out.
|
| |
NOTE: Although the pulse
brew process can be used for coffee or tea, it is designed to brew
tea. Because the process of brewing tea is different than coffee,
the brewer works differently when the TEA BREW BUTTON is used. An
On-Off-On cycle is used to steep the tea and provide the maximum
flavor extraction. The action is a cycling of the water flow,
causing the water to go off and come back on. This is normal. |
|
|
|
|
|
The
Pod Holder will not come out of the brewer |
The pod in the POD
HOLDER may have swelled to a point where the holder does not slide
out easily. |
|
|
Wait at least 10 minutes and then try
carefully removing the pod holder again.
|
|
|
|
|
|
Water
is appearing on the counter around the base of the brewer |
The WATER RESERVOIR has
been removed to be filled with water and was not seated properly
when it was replaced. |
|
|
Remove the lid from the
top of the brewer. With firm, but not forceful pressure, press down
on both sides of the reservoir to ensure that the seal in the bottom
of the reservoir seats properly. Replace the lid and watch for
additional water around the base of the brewer. |
|
|
|
|
|
Water
leaks out around the sprayhead |
Replace a damaged seal
or tighten a loose sprayhead. |
|
|
Refer to Assembling
The Sprayhead/Sea and
iInspecting
The Sprayhead/Seal sections for detailed information on how to
resolve sprayhead leaks.
|
|
|
|
|
|
The
POD HOLDER RELEASE BUTTON indicator is not on all the time |
When the BUNN button
(Also known as the POD HOLDER RELEASE BUTTON) is lit, this indicates
that the power to the machine is on. |
|
|
No action is required.
The BUNN Pod brewer is ready to brew. |
|
When the brewer enters a
sleep mode the POD HOLDER BUTTON will not be glowing. |
|
|
Pressing any button or
the POD HOLDER RELEASE BUTTON will wake up the brewer. |
|
NOTE: If the brewer does
not operate, refer to the first situation listed in the beginning of
this troubleshooting section. . |
|
|
|
|
|
HEATING INDICATOR comes on when the COFFEE or TEA button is pressed |
The HEATING INDICATOR
will glow when the tank is bringing water up to brew temperature. |
| |
|
Wait for the HEATING
INDICATOR to go out. When the Indicator has gone out, a brew cycle
can be started. |
|
|
|
|
|
|
HEATING INDICATOR comes on during a brew cycle. |
|
The water entering the
internal tank is being heated for the next brew cycle. |
| |
|
No action is required.
As the heated water is being emptied to brew a serving, new water
enters the internal tank. The brewer senses this new water and
activates the tank heater to heat the water for the next brew cycle.
The indicator coming on during a brew cycle is normal. |
