ROUTINE CLEANING
Before beginning any cleaning procedure, unplug the brewer to avoid the
accidental start of a brew cycle. Clean the pod holder, drip tray and drip
tray grate after each use, using a damp cloth and mild detergent and rinse.
With the pod holder and drip tray removed, use a damp cloth with mild
detergent to wipe the area below the pod holder and into the drip tray area.
Occasionally, wipe the outside of the brewer with a damp cloth. (The
reservoir, slide lid, pod holder, drip tray and drip tray grate are
dishwasher safe.) |
 |
|
PERIODIC CLEANING/DESCALING
(Recommended At Least Once a Month.)
Periodically, you should clean and descale
the brewer to clear any mineral deposits that may have accumulated due to
impurities in the water source. If these deposits are not removed, they can
impair the operation of the brewer and reduce the product life. There are
several products available specifically for descaling. We recommend using
URNEX Activated Descaler available on
our
web site. (White vinegar can be used to descale if a descaling product
is not available.) Follow the directions as printed on the manufacturer's
package. |
|
1.
|
 |
Fill the
reservoir with descaling product as described by the manufacturers
directions, or 1 quart (32 oz.) of white vinegar. Do not add powder
mix directly to the reservoir. Descaling product must be mixed into a
solution before it is added to the reservoir). |
|
2.
|
|
Place an
empty pod holder into the brewer. Be sure the holder is locked into
place, and set the VOLUME CONTROL SLIDE LEVER to the maximum position.
(12 oz.) |
|
3.
|
|
Place an
empty cup or bowl on the drip tray grate that will hold at least 14
oz. of liquid, and press the COFFEE BREW BUTTON to start a brew cycle. |
|
4.
|
|
Once the
brew cycle has finished, empty the cup and set it back onto the drip
tray grate. Press the COFFEE BREW BUTTON again to start a second brew
cycle. |
|
5.
|
|
Once the
brew cycle has finished, empty the cup and the remaining solution, or
vinegar from the reservoir. Remove the Pod Holder; clean the reservoir
and pod holder thoroughly using a mild detergent, then rinse. |
| |
|
NOTE: There is now descaling solution in
the internal tank. Follow the manufacturers directions if the
solution must be left in the tank for any period of time. For vinegar,
allow the solution to sit for at least two, but no more that four
hours. |
|
6. |
|
Fill the
reservoir to the maximum line with fresh clean cold water and place
the pod holder back into the brewer. |
|
7. |
|
Place the empty cup or bowl back onto the
drip tray grate and press the COFFEE BREW BUTTON to begin a brew
cycle. |
|
8. |
|
When the cycle has finished, empty the
cup. Repeat step 7 at least two more times to remove the solution from
the tank. |
|
9. |
|
Clean the
pod holder with a mild detergent and rinse thoroughly. |
|
10. |
|
Proceed to
the Cleaning The Sprayhead/Seal section. |
|
|
|
|
CLEANING THE SPRAYHEAD / SEAL |
|
1.
|
|
Press the
Power Switch into the off position. |
|
2.
|
|
Unplug the
brewer and allow it to cool down. (Minimum of 1 hour.) |
|
3.
|
|
After the unit
has been allowed to cool, remove the pod holder and set aside. |
|
4.
|
|
Using your
fingers, rotate the sprayhead/seal assembly clockwise until the
sprayhead and seal are removed. |
| |
|
NOTE: If the sprayhead and seal
are separated, they must be reassembled as they were when removed from
the brewer.
NOTE: See Assembling
Sprayhead/Seal and Inspecting
Sprayhead Seal located further down page for more information. |
|
5.
|
|
Clean the
sprayhead and seal with a mild detergent and rinse thoroughly. |
|
6.
|
|
Using your
fingers, rotate the sprayhead/seal assembly counter-clockwise until it
is finger tight. |
|
7.
|
|
Replace the
pod holder. |
|
8.
|
|
Plug in the
brewer and press the POWER SWITCH to restore power to the brewer. |
|
10.
|
|
Place decanter
on base plate and plug in the brewer. Allow the water in the tank to
reach brewing temperature before using (approximately 15 minutes). |
|
|
|
| ASSEMBLING THE
SPRAYHEAD / SEAL |
| If the sprayhead and seal are separated
during removal or cleaning, they must be reassembled properly. |
|
1.
|
|
Identify the
top of the seal. The top of the seal that seats against the roof of the
sprayhead ramp has a rough ridge that can be felt by running your
fingers across the surface of the seal. The bottom is smooth. |
|
2.
|
|
Identify the
top of the sprayhead. The top of the sprayhead has a star pattern and a
threaded hole where the sprayhead attaches to the brewer. |
|
3.
|
|
While
carefully stretching the seal, guide the sprayhead into the channel of
the seal. Make sure it is completely in the channel. |
|
| When properly assembled, the sprayhead will
slide easily into the channel of the seal and will not cause any buckles in
the surface of the seal. If the sprayhead seems to be difficult to seat, and
you must stretch the seal more than a slight tug, the assembly is not
together correctly.
|
|
|
INSPECTING THE SPRAYHEAD SEAL
When disassembling your brewer for cleaning,
inspect the sprayhead seal for cracks, tears and holes. Although the seal
should last for an extended period of time, damage can occur through
handling.
Replace the seal if it becomes damaged. This
part is available to
order online. |
|
|
CLEANING THE POD HOLDER
To prevent residue build up, it is a good idea
to periodically disassemble the pod holder/screen assembly and clean it with
a mild detergent. |
|
1.
|
|
Press and hold the POD RELEASE BUTTON while sliding the pod holder out. |
|
2.
|
|
Flip the POD HOLDER upside down and place the holder cavity over the
palm of your hand. |
|
3.
|
|
Using a small object, press the tab of the POD HOLDER INSERT through the
hole in the bottom of the pod holder to remove. |
|
4.
|
|
Clean the screen and holder using a mild detergent and rinse.
(Dishwasher Safe) |
|
5.
|
|
Press the insert back through the hole in the bottom of the POD HOLDER. |
|
| |
CYCLING THE
BREWER
If the brewer has not been used for an extended period of time, it is a good
idea to cycle your brewer before brewing a cup of coffee or tea. |
|
1.
|
|
Remove the reservoir and pod holder from the brewer, clean with a mild
detergent and rinse. |
|
2.
|
|
Refill the reservoir to the maximum line. |
|
3.
|
|
Insert an empty pod holder into the brewer. |
|
4.
|
|
Set the volume control lever to the maximum setting. |
|
5.
|
|
Place a bowl or cup on the drip tray grate that will hold at least 14
oz. |
|
6. |
|
Press the coffee brew button. |
|
7. |
|
When the brew cycle has ended and water drip out has stopped, carefully
remove the pod holder and remove any excess water. |
|
You are now ready to brew. |
|
|
STORING THE
BREWER
Unplug the brewer and wait for it to cool. If your Pod brewer has been used,
it must be stored above 32ºF
to prevent damage to the internal water tank. Empty and dry the water
reservoir before storing. |
| NOTE: Water will remain
in the internal tank. If stored for an extended period of time, refer to
Cycling The Brewer section above before using. |
